Gecko [ www.utparral.edu.mx ]

Name	Size	Permission
grub.d	[ DIR ]	drwxr-xr-x
acpid	346 B	-rw-r--r--
acpi-support	4.81 KB	-rw-r--r--
alsa	638 B	-rw-r--r--
amd64-microcode	328 B	-rw-r--r--
anacron	830 B	-rw-r--r--
apport	149 B	-rw-r--r--
avahi-daemon	219 B	-rw-r--r--
console-setup	285 B	-rw-r--r--
cron	150 B	-rw-r--r--
dbus	297 B	-rw-r--r--
grub	1.18 KB	-rw-r--r--
im-config	1.71 KB	-rw-r--r--
intel-microcode	1 KB	-rw-r--r--
irqbalance	1.36 KB	-rw-r--r--
kerneloops	84 B	-rw-r--r--
keyboard	150 B	-rw-rw-r--
locale	285 B	-rw-r--r--
named	89 B	-rw-r--r--
networkd-dispatcher	152 B	-rw-r--r--
openvpn	1.16 KB	-rw-r--r--
rsync	2.01 KB	-rw-r--r--
saned	110 B	-rw-r--r--
ssh	133 B	-rw-r--r--
ufw	1.85 KB	-rw-r--r--
useradd	1.09 KB	-rw-r--r--

Code Editor : rsync

# defaults file for rsync daemon mode
#
# This file is only used for init.d based systems!
# If this system uses systemd, you can specify options etc. for rsync
# in daemon mode by copying /lib/systemd/system/rsync.service to
# /etc/systemd/system/rsync.service and modifying the copy; add required
# options to the ExecStart line.

# start rsync in daemon mode from init.d script?
#  only allowed values are "true", "false", and "inetd"
#  Use "inetd" if you want to start the rsyncd from inetd,
#  all this does is prevent the init.d script from printing a message
#  about not starting rsyncd (you still need to modify inetd's config yourself).
RSYNC_ENABLE=false

# which file should be used as the configuration file for rsync.
# This file is used instead of the default /etc/rsyncd.conf
# Warning: This option has no effect if the daemon is accessed
#          using a remote shell. When using a different file for
#          rsync you might want to symlink /etc/rsyncd.conf to
#          that file.
# RSYNC_CONFIG_FILE=

# what extra options to give rsync --daemon?
#  that excludes the --daemon; that's always done in the init.d script
#  Possibilities are:
#   --address=123.45.67.89		(bind to a specific IP address)
#   --port=8730				(bind to specified port; default 873)
RSYNC_OPTS=''

# run rsyncd at a nice level?
#  the rsync daemon can impact performance due to much I/O and CPU usage,
#  so you may want to run it at a nicer priority than the default priority.
#  Allowed values are 0 - 19 inclusive; 10 is a reasonable value.
RSYNC_NICE=''

# run rsyncd with ionice?
#  "ionice" does for IO load what "nice" does for CPU load.
#  As rsync is often used for backups which aren't all that time-critical,
#  reducing the rsync IO priority will benefit the rest of the system.
#  See the manpage for ionice for allowed options.
#  -c3 is recommended, this will run rsync IO at "idle" priority. Uncomment
#  the next line to activate this.
# RSYNC_IONICE='-c3'

# Don't forget to create an appropriate config file,
# else the daemon will not start.

${this.title}

Code Editor : rsync